Rust Converter and Primer: Gallon -- One Step to Remove Rust and Prime Surface

Description

ADCOAT RUST CONVERTER AND PRIMER
The best way to eliminate and remove rust from metal
ONE-STEP SOLUTION:
This powerful paint chemically penetrates and converts existing rust and leaves behind a high quality latex metal primer. No need for sanding or sandblasting. It paints on milky white and once the chemical conversion takes place, the rust is eliminated and the paint dries to a black, primed and paintable surface. By sealing out moisture, it extends the life of metal equipment and prevents future corrosion.
HOW TO REMOVE RUST FROM METAL:
...and prevent rust from coming back? AdCoat Rust Converter and Primer creates a permanent chemical bond, reacting with rust and converting it to a layer of magnetite; a black iron oxide mineral which does not react with oxygen or moisture. Your new surface will be rust proof. In addition, it doubles as a high quality latex metal primer and bonding agent for oil-based coatings - such as acrylic, enamel, epoxy, polyurethane and moisture-cured urethane - AND waterbased coatings not susceptible to tannin staining.
APPLIED LIKE PAINT:
Once painted on to a rusted surface, rust is permanently converted, primed, sealed and ready for topcoat.
USES:
Ideal for metal equipment and metal structures - marine, industrial, farming, household, automotive, construction and industrial rust problems. Additional details below.
OTHER SIZES:
Available on eBay in
quart
(72004) and
1 gallon
(72001)
as well as 55 gallon
(72055)
and 250 gallon containers
(72250)
via
our website
.
Product features:
Flat Sheen/Dries Black
Reacts With and Converts Rust
Primes and Seals
Topcoats with Most Paints
Eliminates Costly Sandblasting
Protects Against Future Rust
Low VOC – Low Odor
Levels Surface Imperfections
Interior / Exterior
Provides Better Paint Adhesion
Non-Hazardous
Non-Flammable
Non-Corrosive
Easy to Apply: Brush, Roll or Spray
Soap and Water Clean Up
Tolerant of Humid Conditions
USES
:
AdCoat Rust Converter and Primer
is effective on just about any
rusted metal surface
:
Industrial
Oil Rigs
Storage & Fuel Tanks
Structural Steel
Manufacturing Equipment
Implements
Fencing and Gates
Pipes
Offshore & Onshore Oil / Gas Facilities
Heavy Engineering
Process Plant
Sheet Metal
Farming
Grain Bins
Farm Equipment
Propane Tanks
Steel Sheds
Fertilizer Storage Units
Marine
Bridges
Ships
Decks & Deck Railing
Boat Trailers
Ferries
Oar Locks
Shipping Containers
Supply Boats
Yachting and Leisure craft
Steel Trawlers
Construction Projects
Maintenance of Steel Factory Roofs
Bridge Maintenance
DOT & DPW Projects
Automotive
Auto Body Restoration
Vehicle Frames
Recreational Equipment
Utility Trailers
Ramps
Floorboards
Quarter Panels
Trucks
Household
DIY Maintenance
Garden Tools
Lawn Equipment
Trailers
Iron Furniture & Railings
Decorative Screens
Pet Housing
Mailboxes
Fences
Read All Directions and Limitations Before Use
SURFACE PREPARATION
:
The type and extent of surface preparation will vary with the nature of the surface, its condition and the type of exposure. The primary purpose of surface preparation is to remove all contaminants that would hinder proper adhesion and to render a sound clean substrate suitable for firm bonding. All surfaces must be clean, dry and free of dust, oil, grease, form releases, wax, polish, mold/mildew, loose rust scale, loose or peeling paint, salts and other debris or surface contaminants.  Clean with a strong detergent or power wash to clean surface. For heavy oil deposits several cleanings may be necessary.
ADCOAT Rust Converter and Primer
works best on clean, tightly adhered rust and well bonded old paint
.
It is also proven effective on new degreased or mild steel where flash-rusting has occurred.
Warning:
If you scrape sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear NIOSH-approved respirator to control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourself and family by contacting the U.S. EPA/Lead Hotline at 1-800-424-LEAD (5323) or log on to
www.epa.gov/lea
d
MIXING:
Stir
ADCOAT Rust Converter and Primer
thoroughly by hand avoiding air entrapment.
Do Not Thin.
APPLICATION:
Remove loose rust and peeling paint with a wire brush, then apply
ADCOAT Rust Converter
by brush, roller, or sprayer in one continuous coat measuring 8-10 mils wet thickness. Make sure no pinholes or air bubbles are left on the coating. Check mils thickness throughout application making sure to recoat where mil reader cuts into surface. A test patch is always recommended first.
Once the white coating changes to black, rust conversion has begun. If a grey coating appears, a second coat of
ADCOAT Rust Converter and Primer
can be applied while the first coat is still tacky. A second coat of
ADCOAT Rust Converter
will provide a greater level of protection.
Note, if the surface is very hot, mist with water before applying
ADCOAT Rust Converter and Primer.
COVERAGE
:
Up to
200
square feet per gallon dependent upon surface condition and profile.
NOTE
Estimates do not account for surface irregularity, porosity, of substrate, applicator technique or overspray.
DRY TIME:
Allow to dry 24 hours before applying topcoat.
TOPCOATING
: Apply all topcoats according to manufacturer’s specifications.
ADCOAT Rust Converter and Primer
is an excellent bonding agent for oil-based intermediate and finish coatings of epoxy, enamel, acrylic, polyurethane and moisture-cured urethane. Water based coatings may require an oil based stain blocker as an intermediate application if they are subject to tannin staining.  Use oil based marine or
industrial coatings
for best weather protection.  A test patch is always recommended.
CLEAN UP
:
Clean spills/splatters and equipment immediately with soap and water. If it sets-up or dries use mineral spirits or lacquer thinner to remove.
SHELF LIFE:
Up to 2 years from the date of manufacture when properly stored.
LIMITATIONS:
DO NOT store below 45°F or above 90°F.
DO NOT apply over frozen or frosted substrates.
DO NOT reuse empty container. Recycle or dispose of material properly.
DO NOT apply if rain is forecasted within 24 hours.
DO NOT thin, add or mix any material with the coating unless approved by manufacturer.
DO NOT paint in direct sun or on hot surfaces that exceed 90°F.
DO NOT use acetone or mineral spirits for surface preparation.
PRODUCT DATA:
Weight: 8.85 lbs./gallon
Conforms to ASTM D 1475
VOC: <50 g/L
Conforms to ASTM D 3960
Viscosity: 90±2 KU
Fire Rating: Class A
Conforms to ASTM E 84
SAFETY INFORMATION SUMMARY:
KEEP OUT OF REACH OF CHILDREN.
DO NOT TAKE INTERNALLY.
KEEP FROM FREEZING.
Read the material Safety Data Sheet (MSDS) for this product prior to use.
Contain spilled material and remove with inert absorbent. Dispose of contaminate absorbent, container and unused contents in accordance with local, state and federal regulations.
WARNING! MAY CAUSE SKIN OR EYE IRRITATION.
CAUTION!
Do not take internally. Avoid contact with eyes and skin. Wear protective clothing, gloves and eyewear. Wash hands after using. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection. Keep container closed when not in use. Do not transfer contents to other containers for storage.
First Aid:
In case of contact with eyes and/or skin, flush area with clean water for a minimum of 15 minutes and, if irritation persists, seek medical attention. If ingested, seek medical attention immediately.
LIMITED WARRANTY
Adcoat Industries LLC warrants that this product meets manufacturing specifications. If this product does not meet these specifications, the manufacturer will, at its option and upon proof of purchase, either furnish an equivalent amount of new product to you or refund the purchase price of this product. Adcoat Industries LLC will not be responsible for (1) labor or the cost of labor for the removal or application of any product; (2) delivery delays or any costs incurred due to delivery delays; or (3) any incidental or consequential damages, weather based on breach of expressed or implied warranty, negligence, strict liability, or any other legal theory.
It is our goal to provide our customers with accurate information. To the best of our knowledge, the data contained herein is true and accurate at the date of issuance, but is subject to change without notice. Data reflects information obtained through testing performed at optimum conditions. Actual results may vary.